How Much Does It Cost To Repair A 2001 Toyota Avalon Gear Shift

Avalon A1066 series troubleshooting and solutions

I. Miner indicator

Miner indicator	Normal functioning	Error occurred
Red light	Flashes for 1S, the miner is powered on.	Lights upward continuously, the system is overheated.
White lite	keeps on for 3S. Press the FUNC fundamental to enter the configuration mode.	Frequent flashing, you lot need to printing the FUNC key to make the principal control work ordinarily.
The yellowish	Light keeps on for 20-30s. The system starts to fix.	The xanthous calorie-free does non turn to the green light continuously, and the miner has no hash charge per unit
Dark-green light	Keeps on and the miner starts mining

Restore manufacturing plant settings: When power on (before the indicator flashes ruby), press the FUNC office key for five seconds until the white light flashes to indicate success, and so press RESET or disconnect the power to restart.

Ii. Miner failed to boot

The miner fan does not plough, or the LED lights up after the miner is turned on.

At that place may be the problem:

(1) The fan wiring of the miner is loosened;

(ii) The power supply line of the MM lath of the miner is disconnected;

(3) The Air-conditioning ability input is non connected properly;

(four) The power supply module (PMU board) is damaged;

(v) The command board (MM board) is damaged;

(half-dozen) Power output short circuit protection.

Troubleshooting and repair methods:

(i) Power on the whole miner, turn on the power switch of the miner, and insert the network cable continued to the switch (or router); cheque that the LINK lite of the network port is flashing;

(2) If the network port light does non calorie-free upwardly, it ways that the MM command board is out of power; bank check the ability string connection, supercede the power supply, or check whether at that place is a short circuit in the power output;

(3) If the network port light is on, only the LED light of the MM control lath is off, you need to replace the MM command lath;

(4) If the MM control lath LED is on merely the fan does not turn, bank check the fan cable or replace the fan.

III. The Miner cannot mine

There may exist the problem:

• The mine pool configuration error;

• Network configuration error;

• Miner overheating protection;

• The miner cannot access the external network;

• The miner hash board cannot work;

• The ability supply of the miner has no principal output (wiring error, overload, short circuit, or damage).

Troubleshooting and repair methods:

1. Restore manufacturing plant settings.

After confirming that the network environment is typical, the network cablevision is firmly connected, and the miner is turned on usually, you tin can try to restore the manufactory settings.

ii. Bank check the firmware version of the miner.

Check the firmware version through the backstage, and utilise FMS to update to the current latest version.

three. Check for hash board problems.

(i) Temperature problem.

Check the working status shown in Figure ②: IN Work is normal, OVERHOT means overheating and shutdown;

Nosotros need to continue to bank check the fan and ambient temperature (you tin can choose the GS320 infrared thermometer).

(two) Hash lath failure.

Bank check the number of the hash board shown in Figure ③. The standard value is 3; other values indicate that the hash lath is abnormal.

(3) Power supply trouble.

If the hash board value is 0, the power supply may non supply power typically.

4. Check power supply, temperature, network condition, fan status (click "LOG" in the left column).

Figure ② If only the odd-numbered items have information and the even-numbered items are 0, it means that the Antpool is currently disconnected and not restored;

Figure ③ Normal is InWork

Figure ④ Hash lath should be 3;

Figure ⑤ Temp is the air inlet temperature, which cannot exceed 35°C;

Max is the highest bit temperature, which cannot exceed 85°C;

TAvg is the boilerplate chip temperature and cannot exceed 68°C.

Figure ⑥ If you see that any of the above temperature items is too high, you lot need to cheque the fan speed (you can choose the light amplification by stimulated emission of radiation tachometer to bank check it);

If the fan speed is average, you need to lower the indoor temperature and ensure good ventilation around the miner.

Figure ⑦Vo is the average chip voltage, which is usually 32x.

Figure ⑧PS is the power state. The meanings of items ane-6 are as follows:

a. Error code: Normally 0. Other values indicate power failure or output short circuit;

b. Voltage supplied to the control board: 12xx usually;

c. The voltage supplied to the hash board: normally between 1200 and 1400;

d. Current output from the ability supply to the hash board: specifically related to the output ability and voltage;

e. The output power of the power supply to the hash board: For the 1066 models, the average value is between 3100-3420;

f. The expected output voltage of the power supply to the hash board: If the 6 parameters of the power supply PS field are all 0, it ways that the control board cannot be continued to the ability supply. Please check the line connection; the ability supply needs to be replaced if the connexion is right.

5. Check whether the configuration of the Antpool, miner, and miner password is correct.

ane) In the backstage of the miner, click on the left column and click on Pool;

2) Bank check whether the configuration of Pool, Worker, Password is the same every bit that of your Antpool;

3) Finally, click the Save button to salve the settings.

6. Check the network settings.

1) Click on Network on the left;

2) Cull the default configuration as DHCP mode;

3) Configure network information;

iv) If the computer's DNS is wrong, you can replace it with a shared address;

Note: After modifying the configuration, you need to click the relieve button to relieve the configuration.

Four. the network configuration data operation method.

Step i: Correct-click the showtime carte du jour and click Run;

Step 2: Search cmd;

Step three: In the pop-up black box window, enter ipconfig/all to detect the figurer configuration network information.

V. The method of restoring factory settings.

Setting method one:

ane. Brand sure that the miner is powered off;

ii. Press the FUNC push button and keep information technology pressed;

3. Power on the miners

4. Keep FUNC in the pressed state until the indicator light of the miner turns white.

Setting method two:

ane. Power on the Miner;

2. Press the FUNC button and go on information technology pressed;

3. Press the RESET button and release;

4. Keep FUNC in the pressed country until the indicator light of the miner turns white.

Source: https://www.zeusbtc.com/articles/asic-miner-troubleshooting/1262-avalon-a1066-series-troubleshooting-and-solutions

Posted by: brownnowerve.blogspot.com

Share this post